Pressing DTF (Direct to Film) transfers onto apparel can be done using a heat press, clothing iron, or Cricut press. Here's a general guide for each method:

Using a Heat Press:

1. Prepare Your Heat Press: Ensure your heat press is set up correctly and preheated to 148°C (298°F), the recommended temperature for the fabric you're using.
2. Position the Transfer: Place the DTF transfer onto the garment with the printed side facing down (adhesive side facing up). Position it in the desired location, ensuring it's straight and centered.
3. Cover with a Heat-Resistant Sheet: Place a heat-resistant sheet or parchment paper over the transfer to protect it from direct heat and prevent scorching.
4. Apply Heat and Pressure: Close the heat press and apply firm pressure for the recommended duration, typically 10 seconds. The ideal time and pressure settings may vary depending on your specific heat press and transfer materials. Refer to the instructions provided with your DTF transfers for guidance.
5. Peel Off the Liner: Once the pressing time is complete, carefully lift the heat press and peel off the liner while the transfer is still warm. Be cautious not to disturb the design or the garment.
6. Cool and Inspect: Allow the garment to cool completely before handling or wearing it. Once cooled, inspect the transferred design to ensure it adhered properly and without any imperfections.
7. Repeat if Necessary: If pressing multiple transfers onto the same garment (e.g., ganged sheets), repeat the process for each transfer, ensuring proper alignment and spacing between designs.

Using a Clothing Iron:

1. Set Your Iron: Adjust your clothing iron to the cotton setting without steam, which typically corresponds to around 148°C (298°F).
2. Position the Transfer: Place the DTF transfer onto the garment with the printed side facing down (adhesive side facing up). Position it in the desired location, ensuring it's straight and centered.
3. Cover with a Heat-Resistant Sheet: Place a heat-resistant sheet or parchment paper over the transfer to protect it from direct heat and prevent scorching.
4. Apply Heat and Pressure: Press the iron firmly onto the transfer area for about 10-15 seconds, applying consistent pressure and moving the iron in circular motions to ensure even heat distribution.
5. Peel Off the Liner: Once the pressing time is complete, carefully peel off the liner while the transfer is still warm. Be cautious not to disturb the design or the garment.
6. Cool and Inspect: Allow the garment to cool completely before handling or wearing it. Once cooled, inspect the transferred design to ensure it adhered properly and without any imperfections.

Using a Cricut Press:

1. Set Up Your Cricut Press: Follow the manufacturer's instructions to set up your Cricut press and preheat it to the recommended temperature for DTF transfers, typically around 148°C (298°F).
2. Position the Transfer: Place the DTF transfer onto the garment with the printed side facing down (adhesive side facing up). Position it in the desired location, ensuring it's straight and centered.
3. Cover with a Heat-Resistant Sheet: Place a heat-resistant sheet or parchment paper over the transfer to protect it from direct heat and prevent scorching.
4. Apply Heat and Pressure: Close the Cricut press and apply firm pressure for the recommended duration, typically 10 seconds. The ideal time and pressure settings may vary depending on your specific Cricut press and transfer materials. Refer to the instructions provided with your DTF transfers for guidance.
5. Peel Off the Liner: Once the pressing time is complete, carefully lift the Cricut press and peel off the liner while the transfer is still warm. Be cautious not to disturb the design or the garment.
6. Cool and Inspect: Allow the garment to cool completely before handling or wearing it. Once cooled, inspect the transferred design to ensure it adhered properly and without any imperfections.

Following these steps will help you achieve professional-quality results when pressing DTF transfers onto apparel using a heat press, clothing iron, or Cricut press. If you have any specific questions or encounter issues during the pressing process, don't hesitate to reach out to our customer service team for assistance.

Absolutely! Our experienced design team can assist with creating custom designs from scratch or modifying existing artwork to fit your specifications. Just let us know your ideas, and we'll work with you to bring them to life.

GozyGear provides DTF transfers in two convenient options:

• Gangsheet: Multiple designs are printed on a single sheet, maximizing efficiency and reducing costs for bulk orders.
• By Size: Designs are printed individually, catering to specific sizing requirements, perfect for smaller orders or intricate designs.

Yes, we specialize in customizing apparel for small businesses, SMEs (Small and Medium Enterprises), and individual consumers. Whether you need branded uniforms, promotional items, or personalized garments, we can help bring your vision to life.

Yes, we do provide dropshipping services for DTF Transfers and Custom Apparel with options to customize your packaging as well.